How to Fix a Leaky Shower Head – You Need to Know

A leaky shower head can be annoying and irritating. Beyond the annoying drip, a leaky shower head can waste thousands of gallons of water per month. This will sound so expensive to most people who have installed the shower in their bathroom. The reason is because of hefty water bills. 

If your shower head is rusty, cracked or old, it may have a problem with leaking. Also, your shower head can be a good condition but can be still leaking. Do run rush to purchase another one. First, evaluate why it is not working well. You don't have to worry or panic again.

What you don't realize is how easy and straightforward is to fix a leaking shower head. It just a simple task that will take only 20 to 30 minutes. In fact, no need to call your plumber. All that you need is the right tools such as an adjustable wrench, a new washer, and a screwdriver. This article will discuss more on how to fix a leaky shower head.

Have you asked yourself this question? What causes a shower head to leak? At many times, it's not easy to identify the source of leaking in your shower head. However, you can identify this problem by using the running water and a flashlight through the shower head. This will give you the green light whether the leak exists. Leaking results from various reasons. The common ones are:

Aging Shower Head

As your shower head ages, it is likely to leak over time. This means that you need to install another one to fix this problem. If you live in an older house that has many original fixtures, then the chances are that your shower in your bathroom needs to be renovated to increase its usability.

If you notice that your shower head has been leaking, the ideas that come to your mind is how to fix or replace it.  This gives you a great opportunity to renovate or remodel your bathroom.

Faulty Installation

You can install a shower head or seek assistance from a plumber. But during this process, there is a probability that leaking will be developed if not done well. During the installation process, a white plumber's tape, in this case, is used and applied to form a link between the tube/pipe and the shower head.

This tape prevents even little water from leaking or leaking again. In this kind of installation, the tap is very important. If you come to notice that leaking is originating from where your shower head is located, then remove your shower head and a white tape that has been used to cover the thread. You need to replace or change the old tape and apply the new white tape and re-set the shower head.

Crack and defect in the Shower Head

You may have noticed that a crack has occurred, but you don't know how to identify it. But you can recognize it by running the water slowly through the shower head. Also, a shining light can be used to locate or pinpoint the crack.

Moreover, it is advisable to remove your shower head and carefully inspect the inside part of it to determine the leaking location. The plumber's putter is what you should use to seal the gap or crack if it is small. If the gap in the shower head is large, discard it and replace it with a new model.

Fixing a Leaky Shower Head

Are you planning to fix your leaking shower head? Here are the easiest steps you should follow: Let us look at every step in details.

Turn Off the Water

The first thing is to locate and turn off the main water supply. This is very important especially when you are inspecting your shower head.  Also, this will avoid unpleasant surprises later on during the process. There may be little water that has been trapped, and that will seep out.

For this reason, keep the towel close by. Your shower head may be leaking because of clogged holes that result from mineral deposits and lime build-up in these holes over a long duration. Remember that if you do not know what the cause of leaking, start here. This is very simple. Shut off the water supply first before you get started with fixing.

Thoroughly Clean your Showerhead

When the water is switched or turned off, the next step is to remove dirt, any build up products and grime that can affect the performance of the appliance. With this, results can be a poor water flow and possible blockages that usually causes leaks.

There are special cleaning products in the market that are good and effective. However, there is a wallet-friendly alternative which is the use of distilled white vinegar. Just mix little distilled white vinegar in the container or a pot of water. 

After that heat it up. I am sure you will be surprised because this results in an excellent cleaning agent that does not contain unnecessary chemicals that can harm or damage your shower. Using a wrench or plier, remove your shower head carefully and put it in the mixture.

You are supposed to wait for a few minutes before shaking the toothbrush to remove stubborn dirt. This should unblock these holes where grime or dirt has been deposited, and this will improve your shower pleasure.

Secure Using Tape

This another important step you should not ignore. Take a look at a washer or the O-ring as this the main part that prevents water on your shower head from leaking out. If this part looks visibly damaged or worn, then this is the best time to replace it with another new item.

If this item seems to be fine, just apply some thread tape to seal the threads which are located on the pipe stem. Do it with a lot of care. This will help the shower head to form a strong, protective seal. It will also prevent any threads on your shower head from seizing.

Re-attaching the Showerhead Plus Turn on the Water

You should hand-tighten your showerhead safely before further tightening using your pliers. Note that this should be done keenly. After this, turn on your water supply again.  Make sure that the water is running smoothly.

Check whether the leaking problem is fixed

Now you can determine whether the leaking problem is fixed. Am sure that, shower head holes are fully fixed, and the leaking problem has been solved. To prove this, simply attach the shower head or faceplate back in place.

Turn on your water supply back and let the water run on the shower head.  Ensure the faucet on your bathroom is completely turned off.  The results should make you smile. If leaking is no longer there, know that you have solved your problem. After this, turn your shower off and inspect keenly any signs of leakage.

Now that you got an idea on how to fixing leakages problem, it is your opportunity to inspect your shower head. The above steps are essential and should help you to solve any leaking problems associated with your shower head. Read the steps, and you will not regret.

You may read also

Join The Discussion